サンプルSDカードの起動時メッセージです。
Texas Instruments X-Loader 1.4.4ss (Aug 19 2010 - 02:49:27)
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.03-dirty (Aug 20 2010 - 20:50:46)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz,
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MB
NAND: 0 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Probing for expansion boards, if none are connected you'll see a harmless I2C error.
No EEPROM on expansion board
Beagle xM Rev A
Die ID #61da00011ff00000015739eb09017009
Hit any key to stop autoboot: 3 2 1 0
mmc1 is available
The user button is currently NOT pressed.
reading boot.scr
** Unable to read "boot.scr" from mmc 1:1 **
reading user.scr
755 bytes read
Running bootscript from mmc ...
## Executing script at 80200000
mmc1 is available
reading ramdisk.gz
19960110 bytes read
reading uImage
3190568 bytes read
Booting from ramdisk ...
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Angstrom/2.6.32/beagleboard
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3190504 Bytes = 3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.32 (ubuntu@ip-10-204-115-71) (gcc version 4.3.3 (GCC) ) #3 PREEMPT Wed Aug 18 15:53:03 UTC 2010
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117760
[ 0.000000] Kernel command line: console=tty0 console=ttyS2,115200n8 mem=80M@0x80000000 mem=384M@0x88000000 mpurate=1000 buddy=none camera=lbcm3m1 vram=16M omapfb.vram=0:8M,1:4M,2:4M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/ram0 rw ramdisk_size=131072 initrd=0x88000000,128M rootfstype=ext2
[ 0.000000] Beagle expansionboard: none
[ 0.000000] Beagle cameraboard: lbcm3m1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 80MB 384MB = 464MB total
[ 0.000000] Memory: 316288KB available (5880K code, 671K data, 204K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Calibrating delay loop... 524.12 BogoMIPS (lpj=2048000)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] tmpfs: No value for mount option 'mode'
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] Beagle cameraboard: registering i2c2 bus for lbcm3m1
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] Unable to get DVI reset GPIO
[ 0.000000] omap_init_mbox: platform not supported
[ 0.000000] Target VDD1 OPP = 4, VDD2 OPP = 2
[ 63.170959] OMAP DMA hardware revision 5.0
[ 63.177246] bio: create slab at 0
[ 63.178527] SCSI subsystem initialized
[ 63.179840] usbcore: registered new interface driver usbfs
[ 63.179992] usbcore: registered new interface driver hub
[ 63.180175] usbcore: registered new device driver usb
[ 63.180572] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[ 63.183288] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 63.183349] twl4030: power (irq 373) chaining IRQs 376..383
[ 63.183654] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 63.185394] regulator: VUSB1V5: 1500 mV normal standby
[ 63.185638] regulator: VUSB1V8: 1800 mV normal standby
[ 63.185852] regulator: VUSB3V1: 3100 mV normal standby
[ 63.187133] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 63.187591] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[ 63.187896] regulator: VDAC: 1800 mV normal standby
[ 63.188140] regulator: VPLL2: 1800 mV normal standby
[ 63.188415] regulator: VSIM: 1800 <--> 3000 mV normal standby
[ 63.188781] regulator: VAUX3: 1800 mV normal standby
[ 63.189147] regulator: VAUX4: 1800 mV normal standby
[ 63.201171] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[ 63.214813] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[ 63.216033] Switching to clocksource 32k_counter
[ 63.224975] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 63.228820] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 63.228881] musb_hdrc musb_hdrc: MUSB HDRC host driver
[ 63.229034] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[ 63.229187] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 63.229217] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 63.229278] usb usb1: Product: MUSB HDRC host driver
[ 63.229309] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[ 63.229339] usb usb1: SerialNumber: musb_hdrc
[ 63.229980] hub 1-0:1.0: USB hub found
[ 63.230041] hub 1-0:1.0: 1 port detected
[ 63.231079] NET: Registered protocol family 2
[ 63.231323] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 63.231964] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 63.232391] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 63.232635] TCP: Hash tables configured (established 16384 bind 16384)
[ 63.232666] TCP reno registered
[ 63.232696] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 63.232727] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 63.233001] NET: Registered protocol family 1
[ 63.233459] RPC: Registered udp transport module.
[ 63.233489] RPC: Registered tcp transport module.
[ 63.233520] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 63.233825] Trying to unpack rootfs image as initramfs...
[ 63.236572] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 63.802917] Freeing initrd memory: 131072K
[ 63.803741] omap-iommu omap-iommu.0: isp registered
[ 63.805511] VFS: Disk quotas dquot_6.5.2
[ 63.805633] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 63.806732] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 63.807617] JFFS2 version 2.2. (NAND) (SUMMARY) c 2001-2006 Red Hat, Inc.
[ 63.808441] msgmni has been set to 874
[ 63.812286] alg: No test for stdrng (krng)
[ 63.812622] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 63.812652] io scheduler noop registered
[ 63.812683] io scheduler deadline registered
[ 63.812866] io scheduler cfq registered (default)
[ 63.872589] OMAP DSS rev 2.0
[ 63.872650] OMAP DISPC rev 3.0
[ 63.872741] OMAP VENC rev 2
[ 63.872985] OMAP DSI rev 1.0
[ 64.209289] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 64.228057] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 64.246124] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 64.264190] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 64.864196] console [ttyS2] enabled
[ 64.874542] brd: module loaded
[ 64.880981] loop: module loaded
[ 64.885253] omap2-nand driver initializing
[ 64.889739] No NAND device found!!!
[ 64.893402] No NAND device found!!!
[ 64.897918] usbcore: registered new interface driver catc
[ 64.903411] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 64.909515] usbcore: registered new interface driver kaweth
[ 64.915191] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 64.922851] usbcore: registered new interface driver pegasus
[ 64.928588] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[ 64.935607] usbcore: registered new interface driver rtl8150
[ 64.941406] usbcore: registered new interface driver asix
[ 64.946960] usbcore: registered new interface driver cdc_ether
[ 64.952941] usbcore: registered new interface driver dm9601
[ 64.958679] usbcore: registered new interface driver smsc95xx
[ 64.964569] usbcore: registered new interface driver gl620a
[ 64.970306] usbcore: registered new interface driver net1080
[ 64.976104] usbcore: registered new interface driver plusb
[ 64.981719] usbcore: registered new interface driver rndis_host
[ 64.987823] usbcore: registered new interface driver cdc_subset
[ 64.993896] usbcore: registered new interface driver zaurus
[ 64.999633] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 65.007751] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 65.014617] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 65.020660] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[ 65.028289] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 65.044372] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 65.050292] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 65.057189] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 65.064514] usb usb2: Product: OMAP-EHCI Host Controller
[ 65.069915] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[ 65.075378] usb usb2: SerialNumber: ehci-omap.0
[ 65.080627] hub 2-0:1.0: USB hub found
[ 65.084503] hub 2-0:1.0: 3 ports detected
[ 65.114746] Initializing USB Mass Storage driver...
[ 65.119842] usbcore: registered new interface driver usb-storage
[ 65.125946] USB Mass Storage support registered.
[ 65.130981] mice: PS/2 mouse device common for all mice
[ 65.136657] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 65.144531] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[ 65.155303] i2c /dev entries driver
[ 65.159423] Linux video capture interface: v2.00
[ 65.164398] omap-iommu omap-iommu.0: isp: version 1.1
[ 65.170837] vpfe_init
[ 65.173706] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 65.286926] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[ 65.294006] Registered led device: beagleboard::usr0
[ 65.299194] Registered led device: beagleboard::usr1
[ 65.305725] Registered led device: beagleboard::pmu_stat
[ 65.312805] usbcore: registered new interface driver usbhid
[ 65.318511] usbhid: USB HID core driver
[ 65.322540] Advanced Linux Sound Architecture Driver Version 1.0.21.
[ 65.329498] usbcore: registered new interface driver snd-usb-audio
[ 65.412200] usb 2-2: new high speed USB device using ehci-omap and address 2
[ 65.420074] No device for DAI omap-mcbsp-dai-0
[ 65.424560] No device for DAI omap-mcbsp-dai-1
[ 65.429077] No device for DAI omap-mcbsp-dai-2
[ 65.433563] No device for DAI omap-mcbsp-dai-3
[ 65.438079] No device for DAI omap-mcbsp-dai-4
[ 65.442596] OMAP3 Beagle SoC init
[ 65.446777] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 65.458251] ALSA device list:
[ 65.461334] #0: omap3beagle (twl4030)
[ 65.465301] oprofile: using arm/armv7
[ 65.469268] TCP cubic registered
[ 65.472534] NET: Registered protocol family 17
[ 65.477111] NET: Registered protocol family 15
[ 65.481689] lib80211: common routines for IEEE802.11 drivers
[ 65.487457] ThumbEE CPU extension supported.
[ 65.491821] Power Management for TI OMAP3.
[ 65.497222] Unable to set L3 frequency (400000000)
[ 65.502166] Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/1000 MHz
[ 65.509582] IVA2 clocking rate: 800 MHz
[ 65.684844] SmartReflex driver initialized
[ 65.689086] omap3beaglelmb: Driver registration complete
[ 65.699798] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 65.708099] registered taskstats version 1
[ 65.712982] fbcvt: 1024x768@60: CVT Name - .786M3-R
[ 65.747711] usb 2-2: New USB device found, idVendor=0424, idProduct=9514
[ 65.754486] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 65.763000] hub 2-2:1.0: USB hub found
[ 65.766937] hub 2-2:1.0: 5 ports detected
[ 65.836395] Console: switching to colour frame buffer device 128x48
[ 65.852325] regulator_init_complete: incomplete constraints, leaving VAUX3 on
[ 65.860107] regulator_init_complete: incomplete constraints, leaving VDAC on
[ 65.867675] omap_vout omap_vout: probed for an unknown device
[ 65.874755] RAMDISK: gzip image found at block 0
[ 66.027008] mmc0: new high speed SDHC card at address 1234
[ 66.044342] mmcblk0: mmc0:1234 SA04G 3.67 GiB
[ 66.049194] mmcblk0: p1 p2
[ 66.061248] usb 2-2.1: new high speed USB device using ehci-omap and address 3
[ 66.196228] usb 2-2.1: New USB device found, idVendor=0424, idProduct=ec00
[ 66.208984] usb 2-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 66.227996] smsc95xx v1.0.4
[ 66.323028] usb0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 06:a3:de:5b:3e:9f
[ 66.592651] usb 2-2.2: new low speed USB device using ehci-omap and address 4
[ 66.730895] usb 2-2.2: New USB device found, idVendor=04f3, idProduct=0103
[ 66.747802] usb 2-2.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 66.777709] input: HID 04f3:0103 as /devices/platform/ehci-omap.0/usb2/2-2/2-2.2/2-2.2:1.0/input/input2
[ 66.802612] generic-usb 0003:04F3:0103.0001: input: USB HID v1.10 Keyboard [HID 04f3:0103] on usb-ehci-omap.0-2.2/input0
[ 66.842071] input: HID 04f3:0103 as /devices/platform/ehci-omap.0/usb2/2-2/2-2.2/2-2.2:1.1/input/input3
[ 66.865753] generic-usb 0003:04F3:0103.0002: input: USB HID v1.10 Device [HID 04f3:0103] on usb-ehci-omap.0-2.2/input1
[ 66.983123] usb 2-2.4: new low speed USB device using ehci-omap and address 5
[ 67.130310] usb 2-2.4: New USB device found, idVendor=093a, idProduct=2510
[ 67.154083] usb 2-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 67.169433] usb 2-2.4: Product: USB OPTICAL MOUSE
[ 67.177001] usb 2-2.4: Manufacturer: PIXART
[ 67.207763] input: PIXART USB OPTICAL MOUSE as /devices/platform/ehci-omap.0/usb2/2-2/2-2.4/2-2.4:1.0/input/input4
[ 67.240051] generic-usb 0003:093A:2510.0003: input: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-ehci-omap.0-2.4/input0
[ 68.686462] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 68.695678] devtmpfs: mounted
[ 68.701782] Freeing init memory: 204K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
[ 71.069641] FAT: bogus number of reserved sectors
[ 71.077514] VFS: Can't find a valid FAT filesystem on dev mmcblk0.
[ 71.528228] FAT: bogus number of reserved sectors
[ 71.536193] VFS: Can't find a valid FAT filesystem on dev mmcblk0p2.
Remounting root file system...
Caching udev devnodes
Populating dev cache
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
udhcpc (v1.13.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Setting up IP spoofing protection: rp_filter.
hwclock: can't open '/dev/misc/rtc': No such file or directory
Fri Aug 20 20:54:00 UTC 2010
hwclock: can't open '/dev/misc/rtc': No such file or directory
Configuring update-modules.
Configuring ti-dsplink-module.
Configuring ti-lpm-module.
Configuring util-linux-ng.
update-alternatives: Linking //bin/dmesg to dmesg.util-linux-ng
update-alternatives: Linking //bin/kill to kill.util-linux-ng
update-alternatives: Linking //bin/more to more.util-linux-ng
update-alternatives: Linking //sbin/mkswap to mkswap.util-linux-ng
update-alternatives: Linking //sbin/pivot_root to pivot_root.util-linux-ng
update-alternatives: Linking //sbin/sln to sln.util-linux-ng
update-alternatives: Linking //sbin/mkfs.minix to mkfs.minix.util-linux-ng
update-alternatives: Linking //sbin/fsck.minix to fsck.minix.util-linux-ng
update-alternatives: Linking //usr/bin/hexdump to hexdump.util-linux-ng
update-alternatives: Linking //usr/bin/last to last.sysvinit
update-alternatives: Linking //usr/bin/logger to logger.util-linux-ng
update-alternatives: Linking //usr/bin/mesg to mesg.sysvinit
update-alternatives: Linking //usr/bin/renice to renice.util-linux-ng
update-alternatives: Linking //usr/bin/wall to wall.sysvinit
update-alternatives: Linking //usr/bin/chfn to chfn.util-linux-ng
update-alternatives: Linking //usr/bin/newgrp to newgrp.util-linux-ng
update-alternatives: Linking //usr/bin/chsh to chsh.util-linux-ng
update-alternatives: Linking //bin/login to login.util-linux-ng
update-alternatives: Error: not linking //sbin/vipw to vipw.util-linux-ng since //sbin/vipw exists and is not a link
update-alternatives: Linking //sbin/vigr to vigr.util-linux-ng
update-alternatives: Linking //usr/bin/reset to reset.util-linux-ng
update-alternatives: Linking //usr/bin/setsid to setsid.util-linux-ng
update-alternatives: Linking //usr/bin/chrt to chrt.util-linux-ng
update-alternatives: Linking //sbin/hwclock to ../bin/busybox
update-alternatives: Linking //sbin/shutdown to shutdown.sysvinit
update-alternatives: Linking //sbin/reboot to reboot.sysvinit
update-alternatives: Linking //sbin/halt to halt.sysvinit
INIT: Entering runlevel: 5
Creating Dropbear SSH server RSA host key.
Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key'
Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCC55WPX2JGlhlpE2W9zHYDsjulND+nXijV8/pGotSLJXvI/qnQkGcq2rfdieN5F1veF8Autw/L8RNPGZz1m5IDwB5EmBfVoMX6PLgCR7NvI0d39oe3JXu3CQh4IYLaniKxOHCs4TxsUL8ps2Qtp9EMIPZFwotWbhTOqhwKVHvF2esT root@beagleboard
Fingerprint: md5 8a:7f:29:e9:0b:21:a4:e2:8e:48:c7:d1:7a:90:8e:dd
Starting Dropbear SSH server: dropbear.
Starting syslogd/klogd: done
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution beagleboard ttyS2
Angstrom 2010.7-test-20100820 beagleboard ttyS2
beagleboard login:
Angstromが起動してますね。
コメント